Fluke 5020A Manual de usuario Pagina 114
- Pagina / 142
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5020A
Users Manual
6-44
Example: SYST:PASS:STAT 1
The <bool> parameter turns the statistics settings password-protection on (1 or ON) or
off (0 or OFF). This command is password protected. Commands protected with this
setting are: CALC:AVER:CLE and DATA:DST... ,
SYSTem:PASSword:TIME?
Returns the state of the date and time password-protection.
Example: SYST:PASS:TIME?
Response: 0
A value of 1 is returned if the date and time password-protection is enabled. otherwise, a
value of 0 is returned.
SYSTem:PASSword:TIME <bool>
Sets the state of the date and time password-protection.
Example: SYST:PASS:TIME 1
The <bool> parameter turns the date and time password-protection on (1 or ON) or off (0
or OFF). This command is password protected. Commands protected with this setting
are: SYST:DATE, SYST:DATE:FORM, SYST:TIME, SYST:TIME:DAYL, and
SYST:TIME:FORM.
Status Commands
The status commands are used for querying and setting the state of the instrument
registers. For details on the operation of the status registers refer to the SCPI standards.
*CLS
Clears the status registers.
Example: *CLS
This clears the error queue, Event Status Register, Operation Status Register,
Questionable Status Register, Alarm Status Register, and Measurement status Register.
*ESE?
Returns the Event Status Enable Register. (See *ESE <num> command below.)
Example: *ESE?
Response: 189
*ESE <num>|MIN|MAX|DEF
This command sets the Event Status Enable Register. This register determines which
event bits of the Event Status Register affect the ESB Event Summary-Message Bit of the
Status Byte Register. If any event bit of the Event Status Register is set (1) while its
corresponding mask bit of the Event Status Enable Register is set, the ESB Event
Summary-Message Bit of the Status Byte Register will be set. The value of the
<numeric_value> parameter is a number from 0 to 255 that is the sum of the binary-
weighted values of each mask bit. The Event Status Register is described in Section
below. The following example causes the ESB bit in the Status Byte Register to be set
whenever a command error or execution error occurs.
Example: *ESE 32
- Users Manual 1
- Table of Contents 3
- ii 4
- Contents (continued) 5
- iii 5
- iv 6
- List of Tables 7
- vi 8
- List of Figures 9
- viii 10
- Chapter 1 11
- Symbols Used 14
- Safety Information 14
- Safety Information 1 15
- Technical Support 16
- Specifications 17
- Environmental Conditions 18
- Quick Start 19
- Introduction 2 21
- Connect the Power Source 22
- Switch the Power On 22
- Measure Temperature 22
- Parts and Controls 23
- Front Panel 25
- Top Panel 26
- Right Side Panel 26
- Left Side Panel 27
- Back Panel 27
- Quick Buttons 28
- Configurations 28
- Accessories 28
- Accessories 3 29
- General Operation 31
- DC Power Source 33
- Battery 33
- Unit of Temperature 35
- Recording Measurements 35
- Sensors 35
- Menu Functions 37
- Channel Menu 39
- Figure 5-3. Channel Menu 40
- Channel Menu 5 41
- Figure 5-6. Sensor Lock 42
- Display Menu 43
- Figure 5-9. Display Menu 44
- Figure 5-10. Display Setting 44
- Display Menu 5 45
- 5-11 47
- Figure 5-14. Graph Scale 48
- Data Menu 49
- Figure 5-17. Data Record 50
- Data Menu 5 51
- 5-15 51
- 5-17 53
- Figure 5-22. Data Storage 54
- Figure 5-23. Data Clear 54
- 5-19 55
- Figure 5-25. Stats Setting 56
- Figure 5-26. Stats View 56
- 5-21 57
- Figure 5-29. Stats Clear 58
- Figure 5-30. Data Card 58
- 5-23 59
- Alarm Menu 60
- Alarm Menu 5 61
- 5-25 61
- Figure 5-35. Sensor Alarm 62
- System Menu 63
- Figure 5-38. System Menu 64
- Figure 5-39. System Setting 64
- System Menu 5 65
- 5-29 65
- 5-31 67
- Figure 5-43. IR 68
- 5-33 69
- Figure 5-45. System Info 70
- Chapter 6 71
- Communications 73
- Interface Commands 74
- Interface Commands 6 75
- 6-11 81
- Commands 82
- 6-13 83
- 6-15 85
- 6-17 87
- 6-19 89
- 6-21 91
- 6-23 93
- 6-25 95
- 6-27 97
- 6-29 99
- Commands 6 101
- 6-31 101
- 6-33 103
- 6-35 105
- 6-37 107
- 6-39 109
- 6-41 111
- 6-43 113
- 6-45 115
- 6-47 117
- 6-49 119
- 6-51 121
- 6-53 123
- Calibration Procedure 125
- Introduction 127
- Equipment 127
- Preparation 127
- Calibration Points 127
- TSLTSLLTS ∆+= 129
- Chapter 8 131
- Maintenance 133
- Troubleshooting 133
- Downloading Recorded Data 135
- CE Comments 136
- Frequently Asked Questions 136
- Index (continued) 141
Relacionado con productos y manuales para De medición, control y control Fluke 5020A
(24 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.082 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales